can i use seatools if i dont have a seagate product

CAN I USE SEATOOLS IF I DONT HAVE A SEAGATE PRODUCT HOW TO
CAN I USE SEATOOLS IF I DONT HAVE A SEAGATE PRODUCT SERIAL NUMBERS
CAN I USE SEATOOLS IF I DONT HAVE A SEAGATE PRODUCT SERIAL NUMBER
CAN I USE SEATOOLS IF I DONT HAVE A SEAGATE PRODUCT SOFTWARE

The apparent lack of activity often gives the impression that the drive or software has stopped responding. On large drives, 10% progress may take as much as 15 minutes.

During the “Long Drive Self Test” progress is reported in 10% increments only.

The highest capacity drives often take 2 to 4 hours to complete.

Because the long tests read every sector on the drive, the amount of time required will depend on the speed and capacity of the disc drive. The long tests will take time to complete. Consider running the long Generic or long DST test, which reads each sector on the drive if you need a more comprehensive test. The “Short Drive Self Test” is adequate for most situations. When you launch the “ Short Drive Self Test” (DST) most drives will run a thorough diagnostic routine that is built in to the hard drive’s firmware.

Long Generic (progress in 1% increments).

Long Drive Self Test (may take up to 4 hours, progress in 10% increments).

Short Drive Self Test (20 to 90 seconds long).

Select the tests that you would like to perform. All Basic Tests are data safe, read-only tests. You may select more than one drive at a time to test them simultaneously.Ī menu of the possible diagnostic tests is shown.

Non-Seagate drives have a silver drive icon. Seagate and Maxtor drives models are given a gold drive icon.

CAN I USE SEATOOLS IF I DONT HAVE A SEAGATE PRODUCT SERIAL NUMBER

However, Seatools for Windows often displays the serial number and even the model number of the internal drive inside the external case, and these numbers do not correspond to the numbers that Seagate assigns to the external unit as a whole.

CAN I USE SEATOOLS IF I DONT HAVE A SEAGATE PRODUCT SERIAL NUMBERS

Seagate serial numbers are alphanumeric and eight characters long. Seagate model numbers begin with the letters “ ST“. This screen also displays information about the drives such as the Model Number and Serial Number. Select the drive you would like to test by making a check mark in the box next to the drive information. Be sure to connect the AC adapter to ensure adequate power during the tests.Īfter SeaTools loads, the screen will list the different storage devices in your system. These tests are disc-intensive and will draw more current than a typical usage profile. Plug in your notebook computer – Notebook systems should not run the long tests using just battery power.Windows XP Control Panel Power Options has a setting “Turn off hard disks” and should be set to “Never” during the test. The drive is working on its own at these times and the system may decide it should go into Stand By or Hibernate modes. A complete drive scan may take a few hours to complete. Keep the computer fully powered on – Power management controls may need to be suspended while doing very long tests.Most desktop and notebook systems have one SATA or PATA internal drive. Internal drives are identified as PATA (Parallel ATA or IDE), SATA (Serial ATA), SCSI or SAS (Serial-Attached SCSI). SeaTools’ Drive Identification – External drives that connect to the system through USB, 1394 Firewire or eSATA do not have the same background activity as the Internal drive.This is harmless to the drive and a routine condition of use however, it causes the SeaTools tests to take much longer time to complete. When that happens, SeaTools will temporarily suspend its current progress while the drive is busy. Otherwise, Windows will continue to give the disc drive commands to access data for the needs of the other applications. The main reason for this is to keep the drive focused on SeaTools as much as possible. Isolate SeaTools – close all other applications before running a hard disc diagnostic.Launch SeaTools by following these steps once it is installed:

CAN I USE SEATOOLS IF I DONT HAVE A SEAGATE PRODUCT HOW TO

This post describes how to run SeaTools for Windows and provides some comprehensive advice about using the test to assist in troubleshooting.

Can i use seatools if i dont have a seagate product